Rack Mounting the Switch
Les procédure de montage du bâti est identique pour tous les commutateurs visés par ce guide. Illustrations dans ce chapitre montrent le montage d’un interrupteur de DCS-7010T-48.
Two-Post Rack Mount
This section provides instructions for mounting the switch in a two-post rack.
To mount the switch onto a two-post rack, assemble the mounting brackets to the chassis, then attach the brackets to the rack posts. Two-post accessory kits include the following parts:
-
2x mounting brackets
- 6x M4x5 flat head Phillips screws.
The following image displays the proper bracket placement for the rack mount.
Attaching Mounting Brackets to the Chassis
- Place the bracket flush on the chassis with attachment pins protruding through key-openings.
Figure 2. Bracket Mount Configuration for Two-Post Rack Mount (Example)
Figure 2. Improper Bracket Mount Configuration for Two-Post Rack Mount (Example)
- Slide the bracket towards the front flange until the bracket clip locks with an audiable click.
Figure 4. Attaching the Mounting Brackets to the Switch Chassis
1 Align the mounting brackets with the attachment pins to obtain the desired mounting position.
4 Bracket clip (attached) 2 Place the bracket flush on the chassis with attachment pins protruding through key openings.
5 Bracket clip (aligned) 3 Slide the bracket toward the front flange until the bracket clip locks with an audible click.
To remove the mounting bracket from the chassis, lift the front edge of the mounting bracket clip with a flathead screwdriver and slide the bracket away from the front flange (opposite from the installation direction).
Inserting the Switch into the Rack
- Attach the bracket flanges to the rack posts.
Figure 5. Inserting the Switch into the Rack
Four-Post Rack Mount
This section provides instructions for mounting the switch in a four-post rack.
The switch is mounted onto a four-post rack by assembling two rails onto the rear posts, sliding the switch onto the rails, then securing the switch to the front posts.
- 2x six-hole mounting brackets
- 2x rail-rods
- 2x rail-slides
The rail-rods and rail-slides assemble into two identical slide-rails.
Each chassis side has attachment pins that align with bracket holes. Pin orientation is symmetric and equidistant, supporting bracket placements where the flange is flush with the front switch panel, flush with the rear panel, or not flush with either panel. Each bracket hole includes a key-opening for placing the bracket flush with the chassis and then locking it into place.
Goupilles de fixation doivent être lock au moins cinq des trous du six support.
| 1 | Bracket not attached by at least 5 pins |
Attaching Mounting Brackets to the Chassis
The following figure displays the front bracket alignment for mounting the switch into a four-post rack.
| 1 | Attaching brackets for front mount |
- Align the mounting brackets with the attachment pins to obtain the desired mounting position.
- Place the bracket flush on the chassis with attachment pins protruding through key-openings.
- Slide the bracket towards the front flange until the bracket clip locks with an audible click.
To remove the mounting bracket from the chassis, lift the front edge of the mounting bracket clip with a flathead screwdriver and slide the bracket away from the front flange (opposite from the installation direction).
Assembling the Rails onto the Equipment Rack
Rail-rods and rail-slides assemble into two identical rails. Each rail connects a front post to a rear post. When the rails are installed, the switch slides on the rails into the rack. Each bracket includes a screw that attaches the switch to the rail.
Each end of an assembled rail contains two rack plugs (Attaching the Mounting Brackets to the Switch Chassis). The rails are installed into a rack by inserting the plugs into rack slots. When installing rails into posts with threaded or rounded holes, remove all plugs located on both sides of the assembled rails, then install the rails with bolts that fit the rack.
| 1 | Attach rail slide to the switch | 4 | Bracket clip (attached) |
| 2 | Slide rail rod onto rail slide | 5 | Bracket clip (aligned) |
| 3 | Attach bracket clip |
- Slide a rail-rod into a rail-slide until the rail clip makes an audible click.
The rail clip prevents the extension of the rail beyond the maximum supported distance between the front and rear rack posts.
Figure 10. Assembling the Rails
1 Rail-slide 3 Rack plugs 2 Rail-rod 4 Rail (assembled) - Attach rail to the right rear rack post by inserting rod-end rack plugs into post slots. The slide assembly must be on the side of the post facing the switch.
If the rack plugs were previously removed, use bolts to attach the rail to the rack.
- Attach the slide end of the rail to the front post by extending the rail end past the post, then contracting the rail while guiding the rack plugs into the post.
- Repeat Step 1 through 3 for the left posts. Ensure the rails are on the same horizontal level.
Figure 11. Attaching the Rails
1 Inset A 2 Inset B
Attaching the Switch to the Rack
- Lift the switch into the rack and insert the mounting brackets into the slide rails.
Figure 12. Inserting the Switch onto the Rails
- Slide the switch on the rails, toward the rear posts, until the mounting bracket flanges are flush with the rail flanges attached to the rack posts.
- Attach the bracket flanges to the rack post using the quick-release thumb screws provided in the accessory kit.
Figure 13. Attaching the Switch to the Rack Posts
